| Capacitance | Rated Capacitance | 4.7uF, 2.2uF | Measuring frequency: 1kHz10%, Measuring voltage: 1Vrms.max. |
| Capacitance Tolerance | K=10% | |
| Voltage | Rated voltage | 100VDC | 1.6*UR Unit:VDC (5 S at 20) |
| Voltage Proof | | No permanent breakdown and flashover | |
| Dissipation Factor (tangent of loss) | | DF0.8% (C1.0uF) | Measuring frequency: 1kHz10%, Measuring voltage: 1Vrms.max. |
| DF1.0% C>1.0uF |
| Insulation Resistance | C0.33uF | IR15000M | measured at rated voltage or less than 100VDC, 1 minute at 20 and RH65% |
| C0.33uF | IR*C3000S |
| Endurance | C/C8%; | | 1000 hours with 125% of rated voltage at 85. |
| DF0.30% (C1uF); DF0.5% (C1uF) | |
| IR 50% of the specified value; | |
| Climatic Catalogue | | 40/85/21 | |
| Solder ability | Solder should cover at least 75% of the circumference of the lead | | solder bath: 2355, bath time: 2.00.5 sec, speed: 256 mm/sec, depth: 1.5+0.5/-0mm from the bottom of the body |
| 75% | |
| |
| Heat shock | C/C5% | | solder bath: 2605, bath time: 5.00.5 sec, speed: 256 mm/sec, depth: 1.5+0.5/-0mm from the bottom of the body |
| DF1.2* | |
| Lead tensile strength | | Pull2.2 LBS, time: 5 sec | |
| Lead bending strength | | Load of lead1.1 LBS | The body of capacitor is bent 90 degrees and returned to its original position |
| Vibration | | Frequency cycle: from 10Hz to 55Hz and then 10Hz, Amplitude: 1.5mm in three directions, Time: 2 hours each directions with a total of 6 hours | |
| Reference Standard | | IEC384-2 grade 1; SJ/T 10787-1996 | |
| Construction | Dielectric | Polyester film | |
| Construction | Electrodes | Vacuum evaporated metal | |
| Construction | Coating | Epoxy resin, fire retardant on request | |
| Construction | Leads | Radial leads of tinned wire | |
| Construction | Terminal contact | Electrically welded | |
| Feature | | High reliable and superior performance in low frequency application, Non-inductive construction, Self-healing | |
| Application | | Filter and noise suppression circuit, Pulse, logic and timing circuit, DC-blocking, by-passing and signal coupling in general communication equipment | |
| Marking | Rated capacitance | e.g., 475 | |
| Rated voltage | e.g., 100VDC | |
| Capacitance tolerance | e.g., K | |
| Manufacturer's symbol | JIMSON (JS) | |
| Outline Drawing | Model | CAP | Color | W Max | H Max | T Max | P 1.0 | D 0.05 | L +5/-10 |
| Outline Drawing | 475K100D01 | 4.7uF | Brown | 26.0 | 21.0 | 10.0 | 22.5 | 0.8 | 25.0 |
| Outline Drawing | 225K100D06 | 2.2uF | Brown | 23.0 | 16.0 | 10.0 | 20.0 | 0.8 | 25.0 |
| Soldering Suggestion | Maximum Soldering Temperature | 270 | 4S |
| Pre-heating | 105 | 1min |
| Soldering | 270 | 4S |
| Storage Environment and Conditions | Storage Environment | Temperature 30, Humidity 70% (MBB not open for 24 months) | |
| Storage Condition | Avoid hydrogen chloride, hydrogen sulfide, sulfuric acid, high temperature and high humidity. | |
