| 1. SPECIFIC REFERENCE DATA |
| Rated Capacitance | 0.01-60uF | Measuring frequency: 1kHz10%, Measuring voltage: 1Vrms.max. |
| Capacitance Tolerance | J=5% / K=10% | |
| Rated Voltage | 250-2000VDC | |
| Voltage Proof | 1.6*U (1 minute at 20) | No permanent breakdown or arcing |
| Dissipation Factor (DF) | DF0.1% (C10uF)
DF0.2% (C<10uF) | (at 20, 1kHz) |
| Insulation Resistance (IR) | C0.33uF: IR30000M
C0.33uF: IR*C5000S | Measured at rated voltage or less than 100VDC, 1 minute at 20 and RH65% |
| Endurance | C/C5%; DF0.40%; IR50% of the specified value | 1000 hours with 125% of rated voltage at 85. After the test |
| Climatic Catalogue | 40/85/21 | |
| Solderability | Solder should cover at least 75% of the circumference of the lead | Solder bath: 2355, Bath time: 2.00.5 sec, Speed: 256 mm/sec, Depth: 1.5+0.5/-0mm from the bottom of the body |
| Heat Shock | C/C5% DF1.2*. Appearance without visible damage. | Solder bath: 2605, Bath time: 5.00.5 sec, Speed: 256 mm/sec, Depth: 1.5+0.5/-0mm from the bottom of the body |
| Lead Tensile Strength | No visible damage. | Pull: 2.2 LBS, Time: 5 sec |
| Lead Bending Strength | No visible damage. | Load of lead: 1.1 LBS. The body of capacitor is bent 90 degrees and returned to its original position. |
| Vibration | No visible damage. | Frequency cycle: 10Hz to 55Hz and then 10Hz. Amplitude: 1.5mm in three directions. Time: 2 hours each direction, total 6 hours. |
| Reference Standard | IEC 60384-16, GB10190 | |
| 2. CONSTRUCTION |
| Dielectric | Polypropylene film | |
| Electrodes | Vacuum evaporated metal | |
| Coating | Encapsulated in reinforced flame retardant plastic case sealed with epoxy resin (UL94V-0) | |
| Leads | Radial leads of tinned wire/insulation flexible wire | |
| Terminal contact | Electrically welded | |
| 3. FEATURES |
| Construction | Non-inductive, self-healing | |
| Moisture Resistance | High property moisture resistance | |
| Environmental Adaptability | Super physical and environmental characteristics | |
| 4. APPLICATION |
| Filtering & Noise Suppression | Filter and noise suppression circuit | |
| Pulse & Logic Circuits | Pulse, logic, and timing circuit | |
| Communication Equipment | Dc-blocking, by-passing and signal coupling | |
| Power Electronics | Peak voltage, peak current absorption protection in switching device turn-off | |
| 5. MARKING (UV ink or laser engraving) |
| Individual Capacitor Marking | Rated capacitance (e.g., 103), Rated voltage (e.g., 2000VDC), Capacitance tolerance (e.g., J), Manufacturer's symbol (JIMSON/JS) | |
| Package Marking | Product type, rating, quantity, date of manufacture, location of manufacture, manufacturer's name | |
| 6. EXPLANATION OF IMPORTANT TERMINOLOGY |
| Rated Capacitance Unit | PF (1F=1,000mF=1,000,000uF=1,000,000,000nF=1,000,000,000,000pF) | Example: 224 = 220,000pF or 0.22uF |
| Capacitance Tolerance Symbols | F=1%, G=2%, J=5%, K=10%, M=20%, N=30% | |
| Dissipation Factor (DF) | Measure of power loss in AC voltage (tg=P/Q) | Standard condition: 20, 1kHz |
| Insulation Resistance (IR) | Measure of ability to retain electrical charge. Ratio of applied DC voltage to leakage current. | T=20, RH65%. Measured 60s after voltage application. |
| Self-healing | Ability of metallized film capacitors to isolate weak points after breakdown by evaporating the metal layer. | |
| 7. WEATHERABILITY TESTING METHODS |
| High Temperature (85) | Capacitance drift: +5% max of initial value. DF: <0.2% (at 1KHz) | After thermal stability |
| Low Temperature (-40) | Capacitance drift: -5% max of initial value. DF: <0.15% (at 1KHz) | After thermal stability |
| Humidity (85, 85% RH for 1000h) | Capacitance drift: +10% max of initial value. DF: <0.2%. IR: >50% of initial value. | After 16h recovery |
| 10. DIMENSION (UNIT: mm) |
| SYMBOL | CAP (uF) | W*H*T (0.5) | L (5) | P (1.0) | D (0.05) | REMARKS |
| MPC103J2000D02 | 0.01 | 18*12*6 | L25 | P15 | CP0.6 | |
| MPC104J630D04 | 0.1 | 18*18*10 | L25 | P15 | CP0.8 | Double film |
| MPC104K520D01 | 0.1 | 13*12*6 | L25 | P10 | CP0.6 | |
| MPC105J1000D01 | 1.0 | 32*20*11 | L3.8 | P27.5 | CP0.8 | |
| MPC105K1000D02 | 1.0 | 41.5*31.4*24 | L25 | P37.5 | CP1.0 | |
| MPC105K450D01 | 1.0 | 18*18*10 | L23 | P15 | CP0.8 | |
| MPC106J650D01 | 10.0 | 41.5*24*19 | L21 | P37.5 | CP0.8 | Four leads, B=12.7 |
| MPC155K100D01 | 1.5 | 15*17*7 | L20 | P12.5 | CU0.8 | |
| MPC155K450D01 | 1.5 | E8 | L25 | P22.5 | CP0.8 | |
| MPC156K1200D01 | 15.0 | 42.5*38*25 | L21 | P37.5 | CU0.8 | |
| MPC156K900D01 | 15.0 | 42*36*23 | L25 | P37.5 | CU0.8 | Black case yellow glue |
| MPC224J630A01 | 0.22 | 18*16*10 | L25 | P15 | CP0.6 | |
| MPC226K1200D01 | 22.0 | 58*40*28 | L21 | P52.5 | CU1.0 | Box type |
| MPC332J1000D02 | 0.0033 | 13*9*4 | L25 | P10 | CP0.6 | |
| MPC332J2000D01 | 0.0033 | 18*12*6 | L25 | CP0.6 | L25 | Gray yellow glue |
| MPC333K1000A01 | 0.033 | 18*12*6 | L25 | P15 | CP0.8 | Double film |
| MPC335K250D01 | 3.3 | 31*25*14 | L25 | P27.5 | CP0.8 | |
| MPC335K450D01 | 3.3 | 32*20*11 | L25 | P27.5 | CP0.8 | |
| MPC473J630D05 | 0.047 | 18*12*6 | L3.8 | P15 | CP0.6 | |
| MPC504J1000D01 | 0.05 | 38*30*20 | L21 | P30.5 | CP0.8 | Black case yellow glue |
| MPC504J1000D02 | 0.05 | 32*33*18 | L3.5 | P27.5 | CU1.0 | Irregular box type |
| MPC565M250D01 | 5.6 | 31*25*14 | L30 | P27.5 | CP0.8 | |
| MPC605K1200D01 | 6.0 | 41.5*31.4*24 | L25 | P37.5 | CP1.0 | |
| MPC606K500D01 | 60.0 | 42.5*50*35 | L21 | P37.5 | CP0.8 | Four leads, B=20.3 |
| MPC805K1000D01 | 8.0 | 32*37*22 | L23 | P27.5 | CP0.8 | |
| 11. CAUTION |
| Soldering Suggestion | Max Soldering Temp: 270, Time: 4S. Pre-heating: 105, 1min. | |
| Salt Fog Test Conditions | Lead wire is tin-plated copper-coated steel. Test after wave soldering. | |
| 12. STORAGE ENVIRONMENT AND CONDITIONS |
| Storage Environment | Temp 30, Humidity 70%. MBB not opened: 24 months storage period. | |
| Storage Condition | Avoid exposure to atmosphere containing hydrogen chloride, hydrogen sulfide, sulfuric acid. Avoid high temperature and humidity. Store under specified conditions. | |
