| Series | 630MMG | |
| Model Number | 630MMG224J | |
| Nominal Capacitance | 0.22F | Marked as '224' |
| Tolerance | 5% | Marked as 'J' |
| Rated Voltage | 630VDC | Marked as '2J' |
| Category Temperature Range | -40+105 (+85) | Voltage derating required beyond +85 |
| Dielectric Loss (tan ) | 0.01 max at 1kHz | |
| Voltage Proof | Rated Voltage 160% for 60s | |
| Insulation Resistance | 15,000M min (between terminals) | |
| Lead Wire | Tin Alloy Annealed copper wire (Sn+3Cu plating, 122m thickness) | |
| Construction Element | Metallized polyester film (Dielectric), Tin Alloy (Metal Spray), Resin (Under Coat), Epoxy resin (Over Coat) | |
| Marking on Product | Nominal capacitance, Tolerance, Rated voltage, Manufacturer's abbreviation ('R'), Series symbol ('G'), Lot number | Marking ink shall be black. |
| Appearance | Lead wire coated with solder completely. No remarkable flaw or pin-hole. | Visual check. |
| Resistance to solvent | No remarkable abnormality on appearance, marking legible. | Isopropyl alcohol. |
| Withstand voltage (between terminal and exterior cladding) | No abnormality. | 200% of rated voltage for 1 to 5 sec. |
| Insulation resistance (between terminal and exterior cladding) | 30,000M min | |
| Strength of termination | Tensile strength: 10N (10 1sec). Bending strength: 5N applied. | |
| Vibration proof | No electrical short circuit or disconnection ( 0.5ms). Stable connecting condition. No abnormality of appearance. | 10 to 55 Hz, 1.5 mm peak to peak amplitude, 2 hrs in each direction (6 hrs total). |
| Resistance to soldering heat | No remarkable abnormality. | Soldering bath: 2605C for 101sec. Soldering iron: 35010C for within 3 sec. (Not possible for Reflow Soldering) |
| Solderability | At least 95% of circumferential surface covered with new solder. | Solder: Sn/3.0Ag/0.5Cu, Flux: Rosin 10%, Solder temp: 2455C, Immersion time: 20.5 sec. |
| Low temperature resistance | No remarkable abnormality. | -402C for 500+24/0 hrs. |
| Heat resistance | No remarkable abnormality. | +1052C for 500+24/0 hrs. |
| Moisture resistance (steady) | No remarkable abnormality. | 90-95% RH, 402C for 500+24/0 hrs. Withstand voltage: 130% of rated voltage for 1 min. Insulation resistance: 4,500M min. |
| Load for moisture resistance | No remarkable abnormality. | 90-95% RH, 402C for 500+24/0 hrs, rated voltage applied. Withstand voltage: 130% of rated voltage for 1 min. Insulation resistance: 4,500M min. |
| Load for higher temperature | No remarkable abnormality. | 125% of rated voltage applied for 1000+48/0 hrs at 852C. Insulation resistance: 7,500M min. |
| Heat cycle | No remarkable abnormality. | -40C (30 min) to 105C (30 min), 100 cycles. Insulation resistance: 7,500M min. |
| Charge and discharge | Variation rate of capacitance: Within 5%. tan : 0.01 max. Insulation resistance: 7,500M min. | 10000 times pulse current application. |
| Cleaning resistance | No deterioration of performance, appearance, size, environment resistance, life etc. | Cleaning solvents: PAINALPHA ST-100S, ST-100SX. Cleaning temp: 40. Methods: Ultrasonic, Immersion, Steam cleaning (1 min each). |
| Permissible current by frequency | Refer to graph | Rated voltage: DC630V / 250Vrms (at 60Hz) |
| Permissible voltage by frequency | Refer to graph | Rated voltage: DC630V / 250Vrms (at 60Hz) |
| Self temperature rise | Within 15C | |
| Storage Condition | Indoor, <30C, <75% RH, no sudden temp changes, direct sunlight, or corrosive gas. | Storage time limit: 1 year from shipped date. |
| Soldering Operation (Iron) | Temp: 350, Duration: within 3 sec. Iron point diameter: within 3 mm. | |
| Packaging Quantity (Inner carton) | 1,000 PCS | |
| Dimensions (mm) | D: 20.0, L: 13.0, H: 10.5, W: 16.5, P: 10.0, d: 0.6 | (for 630MMG224J) |
