| Product Name | Metallized Polyester Film Capacitor (Small Box Type) |
| Reference Standards | GB/T 2693 (IEC 60384-1), GB/T 7332 (IEC 60384-2) |
| Product Structure | 1. Metallized Polyester Film, 2. Spray-Gold Layer, 3. Leads, 4. Flame-retardant Epoxy Resin, 5. Flame-retardant Plastic Case |
| Climatic Category | 55/105/21 |
| Rated Temperature | 85 |
| Operating Temperature Range | -55105 (with derating from +85 to 105) |
| Rated Voltage (DC) | 50/63V, 100V, 160V, 250V, 400V |
| Capacitance Range | 0.001F~1.0F (at 20, 1KHz) |
| Capacitance Tolerance | 5% (J), 10% (K) |
| Withstand Voltage | 1.4UR (5s) |
| Voltage Rise Rate | 100V/s, Cut-off Current: 5mA |
| Dissipation Factor (tan ) | 1.0% (at 20, 1KHz) |
| Insulation Resistance | UR100V: 15000M (CR0.33F), 5000S (CR>0.33F) at 20, 10V, 1min
UR>100V: 15000M (CR0.33F), 5000S (CR>0.33F) at 20, 100V, 1min |
| Lead Strength (Tensile) | 0.3d0.5mm: 5N
0.5d0.8mm: 10N
0.8d1.25mm: 20N (Duration: 101s) |
| Lead Strength (Bending) | 0.3d0.5mm: 2.5N
0.5d0.8mm: 5N
0.8d1.25mm: 10N (Two bends in each direction) |
| Solderability (IEC 68-2-20) | Soldering bath temp: 2355, Immersion time: 2.0s0.5s |
| Resistance to Soldering Heat (IEC 68-2-20) | Soldering bath temp: 2605, Immersion time: 10s1s (Immersion depth 2+0/-0.5mm from mounting surface) |
| Rapid Change of Temperature (IEC 68-2-14) | Temp: -55 to +105, Duration: 30min, Cycles: 5. Capacitance change: 5%, tan change: 0.3% at 1KHZ, Insulation Resistance: 50% of initial |
| Vibration (IEC 68-2-6) | Frequency: 10500Hz, Amplitude: 0.75mm or Acceleration: 98m/s (whichever is less severe) |
| Impact (IEC 68-2-29) | Impacts: 4000 times, Acceleration: 390m/s, Pulse duration: 6ms |
| Dry Heat (IEC 68-2-2) | Temp: +105, Duration: 16 hours. No permanent breakdown or arcing. Capacitance change: 5%, tan change: 0.3% at 1KHZ, Insulation Resistance: 50% of initial |
| Cold (IEC 68-2-1) | Temp: -55, Duration: 2 hours |
| Low Air Pressure (IEC 68-2-13) | Temp: 1535, Pressure: 8.5KPa, Duration: 1 hour (Rated voltage applied during the last minute) |
| Damp Heat Cyclic (IEC 68-2-30) | Test Db, severity b. Rated voltage applied for 1 minute after test completion. |
| Damp Heat Steady State (IEC 68-2-3) | Temp: 402, Humidity: 93 +2/-3 %, Duration: 21 days. Capacitance change: 5%, tan change: 0.5% at 1KHZ, Insulation Resistance: 50% of initial |
| Product Code Rule (Example: W242A682JD2TAAA4JA) | W24: Series Code, 2: Rated Voltage Code (100V), A: Rated Voltage Code (100V), 682: Nominal Capacitance (6.8nF), J: Capacitance Tolerance (5%), D: Lead Pitch Code (5.0mm), 2: Lead Pitch Code (5.0mm), T: Packaging Code (Tape), AAAA: Internal Feature Code |
| Product Dimensions (Example: W242A682JD2TAAA4JA) | CAP: 0.0068uF, R.V: 100V, W: 7.2mm, H: 6.5mm, T: 2.5mm, P: 5.0mm, S: 0.5mm, d: 1mm, L0: 7.2mm |
