| Climate Category | 55/105/21 |
| Rated Temperature | 85 |
| Operating Temperature Range | -55105 (+85 to 105: decreasing factor 1.25% per for VR(dc)) |
| Capacitance Range | 0.0001F~1.0F |
| Capacitance Tolerance | 5% (J); 10% (K) |
| Rated Voltage (DC) | 63V, 100V, 250V, 400V |
| Withstand Voltage | 1.4UR (5s) |
| Dissipation Factor (tan ) | 1.0% (20, 1KHz) |
| Insulation Resistance | UR100V: 15000M or CR0.33F 5000S; CR0.33F (20, 10V, 1min)
UR100V: 15000M or CR0.33F 5000S; CR0.33F (20, 100V, 1min) |
| Lead Strength (Tensile) | 0.3d0.5: 5N; 0.5d0.8: 10N; 0.8d1.25: 20N (Duration: 101 sec) |
| Lead Strength (Bending) | 0.3d0.5: 2.5N; 0.5d0.8: 5N; 0.8d1.25: 10N (Two bends in each direction) |
| Solderability (IEC 68-2-20) | Soldering bath temp: 2355; Immersion time: 2.0s0.5s; Good tinning on lead surface |
| Resistance to Soldering Heat (IEC 68-2-20) | Soldering bath temp: 2605; Immersion time: 10s1s; Capacitance change: 2%; Dissipation change: 0.3% at 1 KHZ |
| Rapid Change of Temperature (IEC 68-2-14) | Temp: -55 to +105; Cycles: 5; Capacitance change: 5%; Dissipation change: 0.3% at 1 KHZ; Insulation Resistance: 50% of initial |
| Vibration (IEC 68-2-6) | Frequency: 10500Hz; Amplitude: 0.75mm or Acceleration: 98m/s; No visible damage or loosening |
| Impact (IEC 68-2-29) | Impacts: 4000; Acceleration: 390m/s; Pulse duration: 6ms; No visible damage or loosening |
| Dry Heat (IEC 68-2-2) | Temp: +105; Duration: 16 hours; No permanent breakdown or arcing; Capacitance change: 5%; Dissipation change: 0.3% at 1 KHZ; Insulation Resistance: 50% of initial |
| Cold (IEC 68-2-1) | Temp: -55; Duration: 2 hours |
| Low Air Pressure (IEC 68-2-13) | Temp: 1535; Pressure: 8.5KPa; Duration: 1 hour (Rated voltage applied in the last minute) |
| Damp Heat (Steady State, IEC 68-2-3) | Temp: 402; Humidity: 93 +2/-3 %; Duration: 21 days; Capacitance change: 5%; Dissipation change: 0.5% at 1 KHZ; Insulation Resistance: 50% of initial |
| Product Dimensions (Example: W222A123JD5L00A00A) | CAP: 0.012F, R.V: 100V, W max: 7.5mm, H max: 7.0mm, T max: 4.0mm, P 0.5: 5.0mm, S 0.5: / , d: 0.5mm, L0 0.5: 1mm |
