| Product Name | Metallized Polypropylene Film Capacitor | |
| Product Structure | Metallized Polypropylene Film, Gold Spray Layer, Leads, Inner Encapsulation Epoxy Resin, Outer Encapsulation Flame Retardant Epoxy Resin | |
| Atmospheric Conditions | Standard Atmospheric Conditions (255), (505)% RH, 86-106kPa | |
| Reference Conditions | Temperature: 25, Humidity: (505)%, Pressure: 86-106kPa | |
| Climatic Category | 40/125/21 | |
| Rated Temperature | 125 | |
| Operating Temperature Range | -40 ~ 125 | (Rated voltage: 125) |
| Rated Voltage | 50V, 100V, 250V, 400V, 630V, 1000V | |
| Capacitance Range | 0.001F ~ 10F | (at 25, 1Vrms, 1kHz) |
| Capacitance Tolerance | 5% (J), 10% (K) | |
| Withstand Voltage | 2.0 * Ur (5s) | Voltage application rate: 10V/s; Cut-off current: 50mA |
| Dissipation Factor (tan) | 0.001 (at 25, 1kHz) | |
| Insulation Resistance | 10000M (C0.33F) | (at 25, 100Vdc, 60s) |
| 3000s (C0.33F) | (at 25, 100Vdc, 60s) |
| Lead Strength (Tensile) | Diameter (mm) | Tensile (N) | |
| 0.8 | 20 | |
| 0.8 | 50 | |
| Lead Strength (Bending) | Diameter (mm) | Load (N) | Duration (s) |
| 0.8 | 3 | 5 | Two bends in each of two directions |
| 0.8 | 5 | 5 | Two bends in each of two directions |
| | | | No visible damage to leads after test |
| Solderability | Soldering Pot Temp: 35010 | Immersion Time: 3s0.5s | Good tinning on lead surface |
| Resistance to Soldering Heat | Soldering Pot Temp: 35010 | Immersion Time: 3s0.5s | Immersion depth: 1.5mm0.5mm from mounting surface, using 1.00.1mm insulating shield plate |
| Capacitance Change: C/C0 2% | Dissipation Change: tan 0.001 | |
| Rapid Temperature Change | Temp: 1 = -40; 2 = 125 | Duration: 30min | Cycles: 100 |
| Capacitance Change: C/C0 3% | Dissipation Change: tan 0.002 | Insulation Resistance: Initial measurement value |
| Vibration | Frequency: 10-500-10Hz | Direction & Time: 3 directions, 2 hours each, total 6 hours | Amplitude or Acceleration: 1.5mm or 10g (whichever is lower) |
| | | Product appearance without visible damage or looseness |
| Impact | Impacts: 3 times | Acceleration: 100g | Pulse Duration: 6ms |
| | | Product appearance without visible damage or looseness |
| Sequential Climate Test (Dry Heat) | Temperature: 125 | Duration: 16 hours | Final Measurement: No permanent breakdown or flashover, appearance without visible damage, clear marking |
| Capacitance Change: C/C0 5% | Dissipation Change: tan 0.005 | Insulation Resistance: Initial measurement value * 0.5 |
| Sequential Climate Test (Damp Heat) | Severity: 95% RH, 40 for 48 hours | First Cycle: Cold Temp: -40, Duration: 4 hours | Low Pressure: Temp: 25, Pressure: 10hPa, Duration: 4 hours |
| (Rated voltage applied for the last 10 mins of the test cycle) | | |
| Sequential Climate Test (Damp Heat) | Severity: 95% RH, 40 for 48 hours | Other Cycles: Complete other cycles | After test, apply rated voltage for 1 minute |
| Steady State Damp Heat | Temperature: 402 | Humidity: 90-96% | Duration: 21 days |
| | | Appearance without visible damage, clear marking; Capacitance Change: C/C0 5%; Dissipation Change: tan 0.005; Insulation Resistance: Initial measurement value * 0.5 |
