| Nominal Capacitance | 0.22 uF | Frequency : 1.00.1kHz (Cap.) Voltage : 1V0.2V(rms) |
| Capacitance Tolerance | 20 % | - |
| DC Rated Voltage | 10 V | - |
| Rated Current (DC) | 2A | - |
| DC Resistance | 30mmax. | Measured with 100mA max. |
| Insulation Resistance | 1000Mmin. | Rated Voltage Time : 2 minutes max. |
| Operating Temp. Range | -55 to 85 C | - |
| Storage Temp. Range | -55 to 85 C | - |
| Withstanding Voltage | Rated Voltage x 300% (1 to 5 s) | Charge Current : 50 mA max. Products shall not be damaged. |
| Dimensions (L x W) | 1.00.1 x 0.50.2 mm | - |
| Dimensions (T) | 0.40.1 mm | - |
| Dimensions (e) | 0.170.1 mm | - |
| Dimensions (g) | 0.1 min. | - |
| Dimensions (D) | 0.350.1 mm | - |
| Dimensions (f) | 0.150.1 mm | - |
| Appearance | No defects or abnormalities. | Visual inspection. |
| Solderability | Electrodes shall be at least 90% covered with new solder coating. Products shall be no failure after tested. | Flux : Ethanol solution of rosin, 25(wt)% Pre-heat : 15010C, 60 to 90s Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 240 3C Immersion Time : 31 s Immersion and emersion rates : 25mm / s |
| Resistance to soldering heat | Appearance No damaged Cap. Change Within 7.5% DC Resistance 0.05max. | Flux : Ethanol solution of rosin, 25(wt)% Pre-heat : 15010C, 60 to 90s Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 270 5C Immersion Time : 10 1 s Immersion and emersion rates : 25mm / s Initial values : measured after heat treatment (150+0 / -10 C,1hour) and exposure in the room condition for 484 hours. Then measured after exposure in the room condition for 484 hours. |
| Bending Strength | Appearance No damaged Cap. Change Within 7.5% I.R. Meet the initial rated value. DC Resistance 0.05 max. | It shall be soldered on the glass-epoxy substrate (100400.8mm). Deflection : 1.0 mm Keeping Time : 5 s |
| Drop | Appearance No damaged Capacitance Meet the initial rated value. DC Resistance 0.05max. | It shall be dropped on concrete or steel board. Height : 1m Method : Free fall Attitude from which the product is dropped : 3 directions |
| Bonding Strength | Appearance No damaged Cap. Change Within 7.5% I.R. Meet the initial rated value. DC Resistance 0.05 max. | It shall be soldered on the glass-epoxy substrate. Applying Force (F) : 5 N Applying Time : 5 s |
| Vibration | Appearance No damaged Cap. Change Within 12.5% I.R. Meet the initial rated value. DC Resistance 0.05 max. | It shall be soldered on the glass-epoxy substrate. Oscillation Frequency : 10 to 2000 to 10Hz for 20 minute. Total amplitude 3.0 mm or Acceleration amplitude 196m/s2 whichever is smaller. Time : A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 hours) Preconditioning : Heat treatment (150+0 / -10 C,1hour) |
| Temperature Cycling | Appearance No damaged Cap. Change Within 12.5% I.R. 105M min. DC Resistance 0.05max. | 1 Cycle 1 step : Minimum Operating Temperature +0 / -3C / 30+3 / -0 min 2 step : Room Temperature / within 3 min 3 step : Maximum Operating Temperature +3 / -0C / 30 +3 / -0 min 4 step : Room Temperature / within 3 min Total of 10 cycles Initial values : measured after heat treatment(150+0 / -10C ,1hour) and exposure in the room condition for 484 hours. Then measured after exposure in the room condition for 484 hours. If its doubt, the mesuring has to be done after 1 hours curing at 150+0 / -10C and 484 hours storage. |
| Humidity | Appearance No damaged Cap. Change Within 12.5% I.R. 105 25M min. DC Resistance 0.05max. | Temperature : 402C Humidity : 90 to 95%(RH) Time : 500+24 / -0 hours Initial values: measured after heat treatment (150+0 / -10C , 1hour) and exposure in the room condition for 484 hours. Then measured after exposure in the room condition for 484 hours. If it s doubt, the mesuring has to be done after 1 hours curing at 150+0 / -10C and 484 hours storage. |
| Heat Life | Appearance No damaged Cap. Change Within 12.5% I.R. 473,104 224,474 105M min. 105 25M min. 435 5M min. DC Resistance 0.05max. | Temperature : Maximum Operating Temperature 2 C Test Voltage : Rated Voltage x 150% Charge Current : 50 mA max. Time : 1000+48 / -0 hours Initial values: measured after heat treatment (150+0 / -10C ,1hour) and exposure in the room condition for 484 hours. Then measured after exposure in the room condition for 484 hours. If its doubt, the mesuring has to be done after 1 hours curing at 150+0 / -10C and 484 hours storage. |
