| 1. General Information | Applicable models | R095, R096, R097, R098, R09J, R09P, R09B | |
| Usage environment temperature | -10C to 70C | |
| Storage environment temperature | 0C to 85C | |
| Test condition | Temperature: 5~35C, Moisture: 45~85%HR | |
| 1. General Information | Soldering heat-resistance | 1. Soldering iron Max, 350C5C at 3 sec
2. Auto soldering 260C5C max. at 3 Sec. Preheating temperature of board surface: 100C max. at within 1 minutes.
3. To guarantee the above process at 1 or 2 times. | |
| Country of origin | China | |
| Environmental requisition | RoHS compliant | |
| 2. Construction | Appearance | Every part should be finished, not exist rust flaw, crack and bad plating | |
| Measurements | Under conditions prescribed by design drawing. | |
| 3. Mechanical characteristics | Total rotational angle | 30010 | |
| Rotational torque | 10~200gf.cm | Rotational velocity : 60/sec |
| Detent torque | 80~250gf.cm | |
| Rotational stopper strength | 1 Kgf.cm, 4Kgf.cm, 5Kgf.cm | |
| 3. Mechanical characteristics | Pull-Push Strength of Shaft | 8Kgf, 10Kgf | |
| 3. Mechanical characteristics | Nut tightening strength | 10Kgf.cm | |
| 3. Mechanical characteristics | Shaft wobble | On the tip of the single shaft exert 250gf, Shaft radial deviant be smaller than: 0.7*shaft long L size/20mm | |
| 4. Electrical characteristics | Total resistance | 10% | |
| Resistance taper | A, B, C | |
| End resistance (Terminal :1-2, 2-3) | R10K: 10, 10K>R250K: 20, R<250K: 0.1%R | |
| Ratings power | B Taper: 0.05W, Other taper: 0.025W | |
| 4. Electrical characteristics | Maximum operating voltage | B Taper: 20V DC or 50V AC, Other taper: 12V DC or 25V AC | |
| Slider noise | 100mV | |
| 4. Electrical characteristics | Gang error | 4dB (-40dB~0dB) | *Apply the Dual-Unit only |
| 4. Electrical characteristics | Insulation resistance | 100M at 250V DC | |
| 4. Electrical characteristics | Voltage proof | 300V AC for 1 Minute | |
| 4. Electrical characteristics | Rotational life | 10,000 cycles, 15,000 cycles, 30,000 cycles | On the without load status according to the 600 r./h rotation, permissible resistance change 15% |
| 5. Switch characteristics | Apply | Yes / No | |
| Switch type | Rotate type, Push-Push type | |
| Switch circuit | S.P.S.T | |
| Switch ratings power | Rotate switch: 12V DC 1A, Push-Push switch: 12V DC 0.5A | |
| 5. Switch characteristics | Switch contact resistance | Initial stage: 100 m, after 10,000 cycles: 1 max. | |
| Switch working angle or track | Rotate switch: 5010, Push-Push switch track: 0.5mm or 1.5mm | specific reference to the drawing |
| Switch working torque | Rotate switch: 800gf.cm, Push-Push switch: 7020gf | |
| 6. Waterproof characteristics | Waterproof standard | Grade -7 of Waterproof standard | Potentiometers Shaft and Bush in 1M deep of water, other component sealed after be exposed to the standard atmosphere, after 30 minutes no water into the Potentiometer inner. |
