| General Information | Applicable Models | R095, R096, R097, R098, R09J, R09P, R09B Series |
| General Information | Usage Environment Temperature | -10+70 or -20+70 |
| General Information | Storage Environment Temperature | -40+85 |
| General Information | Test Condition | Temperature: 5~35, Humidity: 45~85%HR |
| General Information | Soldering Heat-Resistance | Manual: Max 3505 at 3 sec. Auto: Max 2605 at 3 sec. Preheating: Max 100 at within 1 min. (1-2 times) |
| Construction | Appearance | Parts should be complete, without rust, cracks, or bad plating. |
| Construction | Dimensions | Under conditions prescribed by design drawing. |
| Mechanical Characteristics | Total Rotational Angle | 30010 |
| Mechanical Characteristics | Rotational Torque | 10~200gf.cm (Rotational velocity: 60/1 Sec.) |
| Mechanical Characteristics | Detent Torque | 80~250gf.cm |
| Mechanical Characteristics | Detent Quantity | 0, 1, 21, 41 |
| Mechanical Characteristics | Rotational Stopper Strength | 3Kgf.cm, 8Kgf.cm, 4Kgf.cm, 5Kgf.cm |
| Mechanical Characteristics | Pull-Push Strength of Shaft | 8Kgf, 10Kgf |
| Mechanical Characteristics | Nut Tightening Strength | 10Kgf.cm |
| Mechanical Characteristics | Shaft Wobble | Radial deviation < 0.7*shaft long L size/20mm at 250gf on shaft tip. |
| Electrical Characteristics | Total Resistance | 20 K20%, K10%, K+/-% |
| Electrical Characteristics | Resistance Taper | B, A, C |
| Electrical Characteristics | End Resistance (Terminal 1-2, 2-3) | R10K: 10; 10KR250K: 20; R250K: 0.1%R |
| Electrical Characteristics | Ratings Power | B Taper: 0.05W, Other Taper: 0.025W |
| Electrical Characteristics | Maximum Operating Voltage | B Taper: 20V DC or 50V AC. Other Taper: 12V DC or 25V AC. |
| Electrical Characteristics | Slider Noise | <100mV |
| Electrical Characteristics | Gang Error | 4dB (-40dB~0dB) or 3dB (-40dB~0dB) (Dual-Unit only) |
| Electrical Characteristics | Insulation Resistance | >100M at 250V DC |
| Electrical Characteristics | Voltage Proof | 300V AC for 1 minute |
| Electrical Characteristics | Rotational Life | 10,000 cycles, 15,000 cycles, 30,000 cycles (Resistance change 15% max. at 600 cycles/hr without load) |
| Switch Characteristics | Applicable | Yes / No |
| Switch Characteristics | Switch Type | Rotary type, Push-Push type |
| Switch Characteristics | Switch Circuit | Single Pole Single Throw (S.P.S.T) |
| Switch Characteristics | Switch Ratings Power | Rotary Switch: 12V DC 1A. Push-Push Switch: 12V DC 0.5A. |
| Switch Characteristics | Switch Contact Resistance | Initial: 100 m max. After 10,000 cycles: 1 max. |
| Switch Characteristics | Switch Working Angle or Track | Rotary Switch: 5010. Push-Push Switch: 0.5mm or 1.5mm (refer to drawing). |
| Switch Characteristics | Switch Working Torque | Rotary Switch: 800gf.cm max. Push-Push Switch: 700300gf. |
| Switch Characteristics | Switch Life | 10,000 cycles |
| Waterproof Characteristics | Waterproof Standard | No apply or Grade -7 (Potentiometer shaft/bush in 1M water, other parts sealed in atmosphere for 30 min, no water ingress) |
