| General Information | Applicable Models | R095, R096, R097, R098, R09J, R09P, R09B Series |
| General Information | Usage Environment Temperature | -10+70 or -20+70 |
| General Information | Storage Environment Temperature | -40+85 |
| General Information | Test Conditions | Temperature: 5~35, Humidity: 45~85%HR |
| General Information | Soldering Heat Resistance | Hand soldering: Max 3505 at 3 sec; Auto soldering: Max 2605 at 3 sec. Preheating of board surface: Max 100 within 1 minute. |
| Construction | Appearance | All parts complete, no rust, cracks, or bad plating. |
| Construction | Dimensions | As per design drawing. |
| Mechanical Characteristics | Total Rotational Angle | 30010 |
| Mechanical Characteristics | Rotational Torque | 10~200 gf.cm (Rotational velocity: 60/1 Sec.) |
| Mechanical Characteristics | Detent Torque | 80~250 gf.cm |
| Mechanical Characteristics | Detent Quantity | 0, 1, 21, 41 |
| Mechanical Characteristics | Rotational Stopper Strength | 3Kgf.cm, 8Kgf.cm, 4Kgf.cm, 5Kgf.cm |
| Mechanical Characteristics | Pull-Push Strength of Shaft | 8Kgf, 10Kgf |
| Mechanical Characteristics | Nut Tightening Strength | 10Kgf.cm |
| Mechanical Characteristics | Shaft Wobble | Radial deviation < 0.7*shaft long L size/20mm at 250gf on shaft tip. |
| Electrical Characteristics | Total Resistance | 50 K20%, K10%, K+ %/- % |
| Electrical Characteristics | Resistance Taper | A, B, C |
| Electrical Characteristics | End Resistance (Terminal: 1-2, 2-3) | R10K: 10; 10KR250K: 20; R250K: 0.1%R |
| Electrical Characteristics | Ratings Power | B Taper: 0.05W, Other taper: 0.025W |
| Electrical Characteristics | Maximum Operating Voltage | B Taper: 20V DC or 50V AC; Other taper: 12V DC or 25V AC |
| Electrical Characteristics | Slider Noise | <100mV |
| Electrical Characteristics | Gang Error | 4dB (-40dB~0dB) or 3dB (-40dB~0dB) (For Dual-Unit only) |
| Electrical Characteristics | Insulation Resistance | >100M at 250V DC |
| Electrical Characteristics | Voltage Proof | 300V AC for 1 minute |
| Electrical Characteristics | Rotational Life | 10,000 cycles, 15,000 cycles, 30,000 cycles (Resistance change 15% max. at 600 cycles/hour without load) |
| Switch Characteristics | Applicability | Applicable / Not Applicable |
| Switch Characteristics | Switch Type | Rotary type / Push-Push type |
| Switch Characteristics | Switch Circuit | Single Pole Single Throw (S.P.S.T) |
| Switch Characteristics | Switch Ratings Power | Rotary switch: 12V DC 1A; Push-Push switch: 12V DC 0.5A |
| Switch Characteristics | Switch Contact Resistance | 100 m max. initially; 1 max. after 10,000 cycles |
| Switch Characteristics | Switch Working Angle or Track | Rotary switch: 5010; Push-Push switch track: 0.5mm or 1.5mm (Refer to drawing) |
| Switch Characteristics | Switch Working Torque | Rotary switch: 800 gf.cm max.; Push-Push switch: 700300gf |
| Switch Characteristics | Switch Life | 10,000 cycles |
| Waterproof Characteristics | Waterproof Standard | Not Applicable / Grade -7 (Potentiometer shaft and bush in 1M deep water, other components sealed. 30 min exposure to atmosphere, no water ingress.) |
