| 1. General Information | Usage Environment Temperature | -10+70 / -20+70 | Selectable options provided. |
| 1. General Information | Storage Environment Temperature | -40+85 | |
| 1. General Information | Test Condition | Temperature: 5~35, Humidity: 45~85%HR | |
| 1. General Information | Soldering Heat Resistance | Manual: Max 3505 at 3 sec. Auto: Max 2605 at 3 sec. Preheating: Max 100 within 1 min. | Guaranteed for 1 to 2 times. |
| 2. Construction | Appearance | Complete, no rust, cracks, or bad plating. | |
| 2. Construction | Measurements | As per design drawing. | |
| 3. Mechanical Characteristics | Total Rotational Angle | 30010 | |
| 3. Mechanical Characteristics | Rotational Torque | 10~200gf.cm | Rotational velocity: 60/1 Sec. |
| 3. Mechanical Characteristics | Detent Torque | 80~250gf.cm | |
| 3. Mechanical Characteristics | Detent Quantity | 0, 1, 21, 41 | Selectable options provided. |
| 3. Mechanical Characteristics | Rotational Stopper Strength | 3Kgf.cm / 8Kgf.cm / 4Kgf.cm / 5Kgf.cm | Selectable options provided. |
| 3. Mechanical Characteristics | Pull-Push Strength of Shaft | 8Kgf / 10Kgf | Selectable options provided. |
| 3. Mechanical Characteristics | Nut Tightening Strength | 10Kgf.cm | |
| 3. Mechanical Characteristics | Shaft Wobble | < 0.7*L/20mm | Applied force: 250gf on shaft tip. L = shaft length. |
| 4. Electrical Characteristics | Total Resistance | 10 K20% / K10% / K+/-% | Selectable options provided. |
| 4. Electrical Characteristics | Resistance Taper | A, B, C | Selectable options provided. |
| 4. Electrical Characteristics | End Resistance (Terminals 1-2, 2-3) | 10 (R10K); 20 (10K250K) | |
| 4. Electrical Characteristics | Rated Power | 0.05W (B Taper); 0.025W (Other Taper) | |
| 4. Electrical Characteristics | Maximum Operating Voltage | 20V DC or 50V AC (B Taper); 12V DC or 25V AC (Other Taper) | |
| 4. Electrical Characteristics | Slider Noise | <100mV | |
| 4. Electrical Characteristics | Gang Error | 4dB (-40dB~0dB) / 3dB (-40dB~0dB) | Applies to Dual-Unit only. |
| 4. Electrical Characteristics | Insulation Resistance | >100M at 250V DC | |
| 4. Electrical Characteristics | Voltage Proof | 300V AC for 1 minute | |
| 4. Electrical Characteristics | Rotational Life | 10,000 cycles / 15,000 cycles / 30,000 cycles | Without load, 600 cycles/hr. Permissible resistance change 15% max. |
| 5. Switch Characteristics | Applicability | Applicable / Not Applicable | Selectable options provided. |
| 5. Switch Characteristics | Switch Type | Rotary Type / Push-Push Type | Selectable options provided. |
| 5. Switch Characteristics | Switch Circuit | Single Pole Single Throw (S.P.S.T.) | |
| 5. Switch Characteristics | Switch Rated Power | Rotary: 12V DC 1A. Push-Push: 12V DC 0.5A. | |
| 5. Switch Characteristics | Switch Contact Resistance | Initial: 100m max. After 10,000 cycles: 1 max. | |
| 5. Switch Characteristics | Switch Working Angle or Track | Rotary: 5010. Push-Push: 0.5mm or 1.5mm (refer to drawing). | |
| 5. Switch Characteristics | Switch Working Torque | Rotary: 800gf.cm max. Push-Push: 700300gf. | |
| 5. Switch Characteristics | Switch Life | 10,000 cycles | |
| 6. Waterproof Characteristics | Waterproof Standard | Not Applicable / Grade -7 | Grade -7: Shaft/bush in 1M water, other parts sealed, 30 min exposure to atmosphere. |
