| Maximum permissible ripple current | Temperature:1052, Voltage:DC.Voltage+peak ripple voltageRated voltage, Ripple frequency: 120Hz | Refer to table |
| Surge | Temperature:1052, Applied voltage: see specification, "ON" position : 30 seconds, "OFF" position :5 minutes 30 seconds, Duration 1000 cycles | 1.No electrical or mechanical damage. 2.Capacitance change within 15%. 3.D.F.smaller than specification volue. 4.Leakage current smaller than specification volue. |
| Temperature Cycle | One Cycle Temperature(): Rated low category temperature3 (303), 25 (3MAX). Time (minutes): Rated low category temperature3 (303), 25 (3MAX). Total number of cycles: 5 | 1.No appearance defect. 2.Capacitance change within 5% 3.D.F.smaller than specification value. 4.Leakage current smaller than specification value. |
| Resistance to Soldering Heat | Warm up time :1202 seconds to reach 1202, Solder bath temperature: 2605, Solder bath composition: Sn-96.5%, Ag-3.0%, Cu-0.5%, Immersion depth: 1.5 to 2.0mm, Immersion duration: 101 seconds | 1.No appearance defect. 2.Capacitance change within 5% 3.D.F.smaller than specification value. 4.Leakage current smaller than specification value. |
| Solder Ability | Solder bath temperature: 2355, Solder bath composition: Sn-96.5%, Immersion depth: 1.5 to 2.0mm, Immersion duration: 101 seconds | A minimum of 95% the immersed surface is to be coated with the new solder |
| Low Temperature Characteristics (Max. Impedance Ratio) | Working Voltage (V): 6.3 to 450 | Z(-40)/Z(+20): 3 to 8; Z(-25)/Z(+20): 3 to 8 |
| High Humidity Storage | Temperature:402, Relative humidity :90 to 95%, Duration 2408 hours | 1.No electrical or mechanical damage. 2.Capacitance change within 15%. 3.D.F.smaller than specification volue. 4.Leakage current smaller than specification volue. |
| Vent | Capacitor diameter: Less than 22.4mm, Applied current(A): 1, Minutes: within 30; Capacitor diameter: More than 22.5mm, Applied current(A): 10, Minutes: 9 | There shall be no explosion, flash, flame, spark or fire from the capacitor during or after the test, nor shall there be expulsion of any metal from the casing |
| Terminal strength: Tensile strength/winding intensity | Tensile test: Diameter of terminal (mm): 0.5d0.8 (Tensile Strength(N): 10, continuedtime 101sec); 0.8d1.25 (Tensile Strength(N): 20, continuedtime 101sec). Winding strength: Diameter of terminal (mm): 0.5d0.8 (winding Strength(N): 5, Awl quality 0.51kg); 0.8d1.25 (winding Strength(N): 10, Awl quality 1.02kg) | 1.No electrical or mechanical damage 2.No appearance damage |
| Vibration | Frequency range : 10 Hz to 55 Hz, Amplitude :1.5 mm, Cycle definition:10Hz to 55 Hz and back to 10Hz, Cycle duration :1 minute, Duration :2 hours per direction (3directions) | 1.No electrical or mechanical damage. 2.No appearance damage |
| Endurance | Capacitors are placed in an oven and applied voltage for 2000 hours at 105. After being restored to 25, capacitors shall meet the specifications | 1.Capacitance change within 20% of the initial value. 2.D.F.change within 200% of the specified value. 3.Leakage current smaller than specification value. |
| Shelf Life | Capacitors are placed in an oven for 1000 hours at 105 without applying rated working voltage. After being restored to 25, capacitors shall meet the specifications | 1.Capacitance change within 20% of the initial value. 2.D.F.change within 200% of the specified value. 3.Leakage current within 200% of the specification value. |
