| Visual | No abnormal exterior appearance | Visual inspection |
| Dimension | See Page 3 | Visual inspection |
| Insulation Resistance | 10,000Mor 500/C (Whichever Is Smaller) | V500V, Rated Voltage; V500V, Applied 500Vdc; Charge Time60sec. |
| Capacitance | Within The Specified Tolerance | Class : NPO/SL; Class : X7R/X5R/X7E |
| Tan | Class (NPO/SL): More Than 30pF : Q 1000; 30pF & Below: Q 400; Max X7R: 2.5%; Class (Z5U/Y5U): 4.0% | C 20C (C : Capacitance , pF) |
| Withstanding Voltage | No dielectric breakdown or mechanical breakdown | V500V : 200% Rated Voltage; 500VV1000V: 150% Rated Voltage; 1000V :120% Rated Voltage for 1~5 sec. Current is limited to less than 50mA. |
| Temperature Capacitance Coefficient | NPO: 30 ppm/; SL: +350~-1000ppm; X7R: 15%; Y5U: +22% ~-56%; Z5U: +22% ~-56% | Class : [C2-C1/C1(T2-T1)] 100%; Class : (C2-C1)/C1 100%; T1: 25; T2: Test temperature; C1:Capacitance at 25; C2: Capacitance at test temperature (T2) |
| Adhesive Strength of Termination | No indication of peeling shall occur on the terminal electrode. | A 5Nf ( 0.5Kgf) pull force shall be applied for 10 1 second. |
| Resistance to Flexure of Substrate | NPO/SL: 5.0%; X7R: 12.5%; Y5U/Z5U: 30.0% | Bending shall be applied to the 1.0 mm with 1.0 mm/sec. |
| Solderability | More than 90% of the terminal surface is to be soldered newly, so metal part does not come out or dissolve. | Solder Temperature : 245 5; Dip Time : 5 0.5 sec.; Immersing Speed : 2510% mm/s; Solder : H63A; Flux :Rosin; Preheat : At 80~120 for 10~30sec. |
| Resistance To Soldering Heat | Cap. Change: Class (NPO/SL): Within 2.5% or 0.25pF (whichever is larger of initial value); X7R: Within 10%; Class Z5U/Y5U: Within 20% | Preheat : At 150 10 For 60~120sec.; Dip : Solder Temperature of 260 5; Dip Time : 10 1sec.; Immersing Speed : 2510% mm/s; Solder : H63A; Flux :Rosin; Measure at room temperature after cooling for Class: 24 2 Hours; Class: 48 4 Hours |
| Temperature Cycle | Cap. Change: Class (NPO/SL): Within 5.0% or 0.5pF (whichever is larger of initial value); X7R: Within 15%; Class Z5U/Y5U: Within 30% | Capacitor shall be subjected to five cycles of the temperature cycle as following: Step Temp.() Time(min) 1 Min Rated Temp. +0/-3 30 2 25 3 3 Max Rated Temp. +3/-0 30 4 25 3 |
| Humidity | Cap. Change: Class (NPO/SL): Within 3.0% or 0.3pF (whichever is larger); X7R: Within 15%; Class Z5U/Y5U: Within 30% | Temperature : 40 2; Relative Humidity : 90 ~ 95%RH; Test Time : 500 +12/-0Hr; Measure at room temperature after cooling for Class :24 2Hrs Class :48 4Hrs |
| High Temperature Load (Life Test) | Cap. Change: Class (NPO/SL): Within 2.5% or 0.25pF (whichever is larger); X7R: Within 7.5%; Class Z5U/Y5U: Within 20% | Temperature : max. operation temperature; Test Time : 1000 +12/-0Hr; Applied Voltage : 120% rated voltage (for capacitance more than 1.0uF in 1210/100V); Current Applied : 50 mA Max. |
| Vibration | Insulation Resistance: To satisfy the specified initial value | Vibrate the capacitor with amplitude of 1.5mm P-P changing the frequencies from 10Hz to 55Hz and back to 10Hz in about 1 min. Repeat this for 2 hours each in 3 perpendicular directions. |
